Yes. For a 2020 Land Rover Defender with 255/60r20 tires the # TC2828 will fit those tires and are a good choice. You can get the chains with the cams included with the Titan Chain Snow Tire Chains w/ Cams - Ladder Pattern - V-Bar Link - 1 Pair # TC2828CAM instead of adding the Titan Chain Multi-Arm Rubber Tire Chain Adjuster for Heavy Trucks - 1 Pair # TCMA3.
I've linked a review video of these chains for you to have a look at. view full answer...
The kit you're looking for to add a Rhino Rack Pioneer Platform and Back Bone system to your 2016 Land Rover LR4 is available with part # RR83AB; this kit contains the Rhino Rack 52107F Pioneer Platform and RD4B1 Back Bone kit. These have been confirmed to fit your LR4.
You could also get a 56" wide platform with part # RR75TB and use the Rhino-Rack Backbone Mounting System for Pioneer Platform - Land Rover LR4 # RRRD4B1. view full answer...
You'll need the # 3035-P brake controller wiring harness. We've found the connector either directly above the brake pedal or nearer the center console. The connector will be gray in color which should make it easier to locate. We do not have an ebay store, we sell directly from our website, etrailer.com. view full answer...
The trailer wiring harness kits we have for your 2017 Land Rover Discovery Sport are all the 4-pole type and all of these aftermarket products require hardwiring. We do not have a plug-and-play 7-way option.
All are shown on the linked page and all will install in the same manner. I suggest Curt kit # C59236 for its higher output current capacity. A helpful installation article is linked for you.
You can convert this 4-pole connector type to a 7-way through installation of our # ETBC7... view full answer...
The best solution available for your 2020 Land Rover Velar is going to be using the SeaSucker Board Carrier # 298-BX1806 which will allow you to carry 2 paddle boards or surf boards on the top of your vehicle. The SeaSucker systems are secured to the top of the vehicle with extremely strong vacuum cups and allow you the flexibility to only have the system mounted when you're carrying boards, since it's easy to install and remove as needed.
If you wanted to have a full roof rack system,... view full answer...
Yes, you will need a brake controller to control your trailer's brakes with your 2011 Land Rover Range Rover. I recommend the Tekonsha Prodigy P3 Trailer Brake Controller item # 90195. This is a proportional brake controller that will activate your 2019 Airstream's brakes in proportion to your Range Rover's braking action. It automatically adjusts the trailer's braking based on deceleration of your vehicle. The brakes will activate immediately so you won't have to worry about pausing like... view full answer...
We do have the feet you need to install your # TH711320 on the 2023 Land Rover Defender 110 with factory tracks. According to Thule, you need the Feet # TH49SC and Fit Kit # TH94CE. view full answer...
While we do not have any grille guards that will work with your 2007 Land Rover LR2, we do have a wide variety of roof racks that'll work great.
If your vehicle has a slick roof, I recommend going with the Thule WingBar Evo Crossbars # TH711400, with the Evo Clamp Feet for Thule Crossbars # TH710501, and the Fit Kit for Thule Evo Clamp and Edge Clamp Roof Rack Feet # TH145123.
These crossbars have integrated t-slots to accompany any roof mounted accessory, has a nice weight capacity at... view full answer...
In order to get a replacement hardware kit for your Curt Trailer Hitch Receiver # 13456, you'll just need to order the Replacement Hardware Kit for Trailer Hitches # RHK.
This kit is going to include everything that would've originally come with the hitch including the fish wire (leader wire).
To order this kit, all you're going to need to do is put "13456" in the "Hitch Item Number" box and add it to your cart. view full answer...
The Curt Trailer Hitch Receiver # C13396 that you referenced will not interfere with the spare tire on your 2015 Land Rover Discovery Sport since it is inside the rear hatch. You can use the linked instructions to help install this hitch on your Discovery Sport.
Keep in mind that all non-trailer loads, like a bike rack or cargo carrier, must be supported by a stabilization strap, like part # 18050, to keep in line with the warranty from Curt.
We do have a wiring harness that has a 4-Way... view full answer...
Curt Class III hitch # 13456 will fit your LR3 with a 2-inch receiver. This is a no-drill installation and you can refer to the linked instructions and the install video showing a 2006 LR3 to see the process.
For a trailer brake controller I recommend Curt's innovative wireless Echo # C51180 which offers easy plug-in installation and that lets you use it in any vehicle that has a 7-way.
If your LR3 has no wiring at all you will use 4-pole kit # C59496 along with 7-way wiring upgrade kit... view full answer...
Yes, I do have a hitch receiver that will fit your 2021 Land Rover Range Rover Sport. It is the Curt Trailer Hitch Receiver item # C13243. This is a Class III hitch receiver with a 8000 lbs towing capacity and a 800 lbs tongue weight. It installs below the rear bumper trim for a hidden design where only the actual receiver is visible. I have attached a picture of the Curt item # C13243 installed on a Range Rover Sport so you can see what the finished product looks like.
To be able to... view full answer...
Thank you for all of the information! The Draw-Tite # 75229 combined with the ZCI # 119250KIT and # ETBC7L wiring for the Curt Echo # C51180 is a fantastic combination for your 2020 Land Rover Range Rover Sport.
To hold the 7-Way connector next to the 2" receiver of your Draw-Tite trailer hitch you just need the Curt Easy Mount Bracket # C58000. This basically secures around the 2" Draw-Tite receiver and then sits to the side so you can carry both wiring connectors that come with the ETBC7L... view full answer...
Thank you for the purchase of the Draw-Tite # 75229 trailer hitch and T-One # 118275 for your 2015 Land Rover Range Rover Sport! We have exactly what you need to mount the 7-Way connector without having to modify anything.
If you use the Easy Mount Bracket # C58000 you can secure the 7-Way to the 2" receiver of your trailer hitch (see attached picture). I have attached a sample installation video of this being installed on a 2005 Tucson for you to reference. view full answer...
I suspect the shank portion of your hitch bike rack is actually the 1-1/4-inch size since we do not have any bike racks with a 1-inch shank. The item you need to convert your 2-inch receiver opening to the 1-1/4-inch size is a reducer sleeve like # HT02. This appears on the linked page with other similar items.
This include a 1/2-inch pin to secure the rack in the reducer and you can use 5/8-inch pin # PC3 to secure the reducer in your 2-inch hitch. view full answer...
You will first need to install a tail light converter like Curt # C59236 on your Land Rover LR3. The link provided will show you all options. Converters vary slightly in the amount of current they can deliver, so if your trailer uses many incandescent lights you might want to choose a converter with higher current capacity. All will install in essentially the same manner.
With a 4-pole installed you will simply add TowReady 4 Pole to 5 Pole Trailer Wiring Adapter # 20036. This includes... view full answer...
If your camper trailer has a 7-Way you need part # 20142 but if it has a 4-Way or 5-Way flat connector then use part # C35FR instead. They both offer the same solution for your 2016 Land Rover LR4 it just depends on what you have on your trailer side. view full answer...
To install the 50" Yakima JetStream crossbars # Y00425 on your 2017 Land Rover Discovery Sport you'll also need the BaseLine Towers # Y28TR as well as fit kits # Y06127 and # Y06154.
When it comes to bike capacity there are a few factors that come into play, but if your bikes are lightweight then you can potentially fit 5 or 6 bikes on 50" crossbars. The factors that you need to take note of are the weight of your bikes, the width of the bike racks you plan on using, and the geometry of... view full answer...
If you have standard size axles that you are installing the Electric Trailer Brake Kit # AKEBRK-7-SA on then you can choose from the following options:
5,200 lb Axle - Kit # BK3-310 (Grease Seal 2.125" ID) or Kit # BK3-300 (Grease Seal 2.250" ID)
6,000 lb Axle - Kit # BK3-110 (Grease Seal 2.125" ID) or Kit # BK3-100 (Grease Seal 2.250" ID)
7,200 lb Axle - Kit # BK3-210 (Grease Seal 2.125" ID) or Kit # BK3-200 (Grease Seal 2.250" ID)
Since you do have an older Airstream Overlander you... view full answer...
The # APT4 Tandem-Axle Hanger Kit will provide about 4 inches of clearance from the center of the trailer axle to the bottom of the trailer frame, with no load on the axle. This is assuming that your axle tube is 3 inches diameter. If your axle tube is smaller the height will be sightly less. The curve of the springs you select will have some affect also.
I would recommend that you go with the APT5 hanger kit because all of the hangers are the same height and it will make it easier to... view full answer...
Go To Results